Add New Sell Offer | My Sell Offers | My Sell Offers | Free Offer Alert
Sell Offers | Buy Offers | Products | Companies

Keyword "rfid module"
advertisements
 Selling 13.56MHz RFID card reader module with IIC or UART interface Selling 13.56MHz RFID card reader module with IIC or UART interface

YST308 series are RFID reader/writer module which pick or send command by UART and IIC ports. YST308 series meet kinds of international contactless IC card standards. Also YST308 series can support kinds of cards from suppliers. YST308 series RF antenna is separated from the module. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna.4wires are linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module’s performance and stability.

Qualifications

Where it can be used: bus, access control system, bank, water meter, etc.

PCD: NXP PN512

Working frequency: 13.56MHz

RF standard: ISO14443A,  ISO14443B

Operating distance: 80mm (depending on card and antenna design)

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

Interface: IIC &UART (selected by SPS pin, IIC is better)

Communication rate: IIC 400Kbps, UART 19.2Kbps/115.2Kbps

Max command length: 1024 Bytes

Interface level: 3.3V (TTL level; 5V tolerance)

Power consumption: 50mA

Dimension: 42mm*21mm*8mm

Package: DIP32

Weight about:15g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

Module

YST308

RF base station

PN512

Interface

IIC, UART

RF standard

ISO14443A, ISO14443B, Mifare

Reading distance

80mm

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B

 

[Related Categories: Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
 Selling 13.56MHz RFID card reader module with IIC or UART interface Selling 13.56MHz RFID card reader module with IIC or UART interface

YST308 series are RFID reader/writer module which pick or send command by UART and IIC ports. YST308 series meet kinds of international contactless IC card standards. Also YST308 series can support kinds of cards from suppliers. YST308 series RF antenna is separated from the module. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna.4wires are linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module’s performance and stability.

Qualifications

Where it can be used: bus, access control system, bank, water meter, etc.

PCD: NXP PN512

Working frequency: 13.56MHz

RF standard: ISO14443A,  ISO14443B

Operating distance: 80mm (depending on card and antenna design)

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

Interface: IIC &UART (selected by SPS pin, IIC is better)

Communication rate: IIC 400Kbps, UART 19.2Kbps/115.2Kbps

Max command length: 1024 Bytes

Interface level: 3.3V (TTL level; 5V tolerance)

Power consumption: 50mA

Dimension: 42mm*21mm*8mm

Package: DIP32

Weight about:15g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

Module

YST308

RF base station

PN512

Interface

IIC, UART

RF standard

ISO14443A, ISO14443B, Mifare

Reading distance

80mm

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B

 

[Related Categories: Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
advertisements
 Selling 13.56MHz RFID card reader module with USB or RS232 interface Selling 13.56MHz RFID card reader module with USB or RS232 interface

YST307 series are RFID reader/writer module which pick or send command by USB and RS232 ports. YST306 series meet kinds of international contactless IC card standards. Also YST307 series can support kinds of cards from suppliers. YST307 series RF antenna is separated from the module. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna. The module is connected to the antenna by the 50Ω cable. It is with flexible antenna size and layout.

Characters:

The module is connected to the antenna by the 50Ω cable. It is with flexible antenna size and layout.

Qualifications

PCD: NXP RC500

Working frequency: 13.56MHz

RF standard: ISO14443A, ISO7816

SAM card slot: 2

Cable to antenna: 60cm, can be custom-made, 0.1-1.5mm

Operating distance: 80 mm (depending on card and antenna design)

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

EEPROM: 4K

Interface: USB or RS232

Max command length: 1024 Bytes

Interface level: 3.3V

Power consumption: 50mA

Dimension: 80mm*60mm*8.5mm

Package: DIP32

Weight about: 100g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

Module

YST307A

YST307C

YST307G

YST307H

RF base station

RC500

RC531

RC400

RC632

Interface

USB, RS232

USB, RS232

USB, RS232

USB, RS232

Data FLASH

4K

4K

4K

4K

Buzzle

yes

yes

yes

yes

RF standard

ISO14443A, Mifare

ISO14443A, ISO14443B, Mifare

ISO15693

ISO14443A, ISO14443B, ISO15693  Mifare

Reading distance

80mm

80mm

80mm

80mm

SAM Card slot

2

2

2

2

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B

I.CODE 1
I.CODE SLI
I.CODE SLI-S
TI Tag-it series
ST LRI series

MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B
 
I.CODE 1
I.CODE SLI
I.CODE SLI-S
TI Tag-it series
ST LRI series
 

[Related Categories: Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
 Selling 13.56MHz RFID card reader module with USB or RS232 interface Selling 13.56MHz RFID card reader module with USB or RS232 interface

YST306 series are RFID reader/writer module which pick or send command by USB and RS232 ports. YST306 series meet kinds of international contactless IC card standards. Also YST306 series can support kinds of cards from suppliers. YST306 series RF antenna is separated from the module. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna. YST306 series RF antenna is separated from the module. The module is connected to the antenna by the 50Ω cable. It is with flexible antenna size and layout. There is a LED lamp holder, can output LED lamp state.

Qualifications

Where it can be used: bus, access control system, bank, water meter, etc.

PCD: NXP RC500

Working frequency: 13.56MHz

RF standard: ISO14443A, ISO7816

SAM card slot:4

Cable to antenna: 60cm, can be custom-made, 0.1-1.5mm

Operating distance: 80 mm (depending on card and antenna design)

Cable to antenna: 60cm, can be custom-made, 0.1-1.5mm

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

EEPROM: 4K

Interface: USB or RS232

Max command length: 1024 Bytes

Interface level: 3.3V

Power consumption: 50mA

Dimension: 105mm*67mm *8.5mm

Package: DIP32

Weight about: 100g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

Module

YST306A

YST306C

YST306G

YST306H

RF base station

RC500

RC531

RC400

RC632

Interface

USB, RS232C

USB, RS232C

USB, RS232C

USB, RS232C

Data FLASH

4K

4K

4K

4K

Buzzle

yes

yes

yes

yes

RF standard

ISO14443A, Mifare

ISO14443A, ISO14443B, Mifare

ISO15693

ISO14443A, ISO14443B, ISO15693  Mifare

Reading distance

80mm

80mm

80mm

80mm

SAM Card slot

4

4

4

4

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B

I.CODE 1
I.CODE SLI
I.CODE SLI-S
TI Tag-it series
ST LRI series

MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B
 
I.CODE 1
I.CODE SLI
I.CODE SLI-S
TI Tag-it series
ST LRI series
 

[Related Categories: Electronics, Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
advertisements
 Selling 13.56MHz RFID card reader with IIC or UART interface Selling 13.56MHz RFID card reader with IIC or UART interface

YST308 series are RFID reader/writer module which pick or send command by UART and IIC ports. YST308 series meet kinds of international contactless IC card standards. Also YST308 series can support kinds of cards from suppliers. YST308 series RF antenna is separated from the module. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna.4wires are linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module’s performance and stability.

Qualifications

Where it can be used: bus, access control system, bank, water meter, etc.

PCD: NXP PN512

Working frequency: 13.56MHz

RF standard: ISO14443A,  ISO14443B

Operating distance: 80mm (depending on card and antenna design)

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

Interface: IIC &UART (selected by SPS pin, IIC is better)

Communication rate: IIC 400Kbps, UART 19.2Kbps/115.2Kbps

Max command length: 1024 Bytes

Interface level: 3.3V (TTL level; 5V tolerance)

Power consumption: 50mA

Dimension: 42mm*21mm*8mm

Package: DIP32

Weight about:15g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

Module

YST308

RF base station

PN512

Interface

IIC, UART

RF standard

ISO14443A, ISO14443B, Mifare

Reading distance

80mm

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 
SR176
SRI512
SRI1K
SRI2K
SRI4K
SRIX4K
T=CL TYPE B

[Related Categories: Electronics, Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
 Selling 13.56MHz RFID card reader module with IIC or UART interface Selling 13.56MHz RFID card reader module with IIC or UART interface

YST304 series are RFID reader/writer module which pick or send command by UART and IIC ports. YST304 series meet kinds of international contactless IC card standards. Also YST304 series can support kinds of cards from suppliers. YST304 series RF antenna is separated from the module. The module is connected to the antenna by the 50Ω cable. It is with flexible antenna size and layout. The RFID module can be very good at reading/writing and very stable for impedance analyzer adjusting between RF circuit and antenna.

Characters:

The module is connected to the antenna by the 50Ω cable. It is with flexible antenna size and layout.

Qualifications

Where it can be used: bus, access control system, bank, water meter, etc.

PCD: NXP CV520

Working frequency: 13.56MHz

RF standard: ISO14443A

Cable to antenna: 60cm, can be custom-made, 0.1-1.5mm

Operating distance: 80 mm (depending on card and antenna design)

Anti collision ability: Full functions anti collision; be able to process multi-card simultaneously; be able to set operate single card only.

Auto detecting card: yes, default OFF

Interface: IIC &UART (selected by SPS pin, IIC is better)

Communication rate: IIC 400Kbps, UART 19.2Kbps/115.2Kbps

Max command length: 128 Bytes

Interface level: 3.3V (TTL level; 5V tolerance)

Power consumption: 50mA

Dimension: 42mm*21mm*8mm

Package: DIP32

Weight about:15g

Operating temperature: -25~+85℃(-77~+185℉)

Storage temperature: -40~+125℃(-104~+257℉)

ISP: Yes

 

 

Module

YST304

RF base station

CV520

Interface

USB, RS232

RF standard

ISO14443A, Mifare

Reading distance

80mm

PICC

 
MIFARE 1K
MIFARE 4K
MIFARE Ultralight
MIFARE Ultralight C
MIFARE Mini
MIFARE DESFire
MIFARE Plus
T=CL TYPE A
 

[Related Categories: Electronics, Card Reader, Access Control Card Reader ]
[Related Keywords: rfid card reader, card reader module, rfid module, 13.56MHz, RFID ]
advertisements
 13.56MHz  HF access controller JMY302 13.56MHz HF access controller JMY302

JMY302 can be connected in the network. There are multiple open-door-modes to choose and multiple time interval & card authority set. And also it is of anti-submarine back; anti-force; anti-destroying and alarming if breaking into when closing the door. It can be use of floor control mode. Meanwhile the set can be operated through SDK in network and firmware is updated online. JMY302 can cooperate with gateway management software and other management software. JMY302 is the four doors entrance guard controller.

  • Qualifications:
  • Door control number: 4 doors
  • Card reader number: 4 sets(2 in / 2 out)
  • Storage record: 4200 times
  • Card capacity: 9999 sheets
  • Interface: RS485 x2, Wiegand x1
  • Output interface: 4 relays
  • Input contact: 4, no-voltage
  • Communication rate: 19200pbs(4800~115200bps)
  • Time interval /Time zone: 32/60
  • Application group / Holiday control: 64/366
  • Controller numbers range: 01~99
  • Anti-submarine back: Max. 3 tiers
  • LCD shows: 8units x 2
  • Keystroke: 16
  • Status indicator: 8LED
  • Buzzer: built-in
  • Operating temperature: -20 ~ +70 ℃ (-68 ~ 158°F)
  • Storage temperature: -40 ~ +80 ℃ (-104 ~ 176°F)
  • Power supply: DC 8V~24V / 0.3~3W
[Related Categories: Other Electronic Accessories, Security Project ]
[Related Keywords: RFID reader, Access controller, rfid module, HF, 13.56MHz ]
 13.56MHz  HF access controller JMY302 13.56MHz HF access controller JMY302

JMY302 can be connected in the network. There are multiple open-door-modes to choose and multiple time interval & card authority set. And also it is of anti-submarine back; anti-force; anti-destroying and alarming if breaking into when closing the door. It can be use of floor control mode. Meanwhile the set can be operated through SDK in network and firmware is updated online. JMY302 can cooperate with gateway management software and other management software. JMY302 is the four doors entrance guard controller.

  • Qualifications:
  • Door control number: 4 doors
  • Card reader number: 4 sets(2 in / 2 out)
  • Storage record: 4200 times
  • Card capacity: 9999 sheets
  • Interface: RS485 x2, Wiegand x1
  • Output interface: 4 relays
  • Input contact: 4, no-voltage
  • Communication rate: 19200pbs(4800~115200bps)
  • Time interval /Time zone: 32/60
  • Application group / Holiday control: 64/366
  • Controller numbers range: 01~99
  • Anti-submarine back: Max. 3 tiers
  • LCD shows: 8units x 2
  • Keystroke: 16
  • Status indicator: 8LED
  • Buzzer: built-in
  • Operating temperature: -20 ~ +70 ℃ (-68 ~ 158°F)
  • Storage temperature: -40 ~ +80 ℃ (-104 ~ 176°F)
  • Power supply: DC 8V~24V / 0.3~3W
[Related Categories: Other Electronic Accessories, Security Project ]
[Related Keywords: RFID reader, Access controller, rfid module, HF, 13.56MHz ]
advertisements
 Sell 13.56MHz RFID Charge controller with display JMY901 Sell 13.56MHz RFID Charge controller with display JMY901

   JMY901 series contactless IC card reader are based the NXP or compatible chip design. The reader supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and ISO7816; various contactless IC card under international standard; especially the contactless CPU cards under ISO14443-4. Meanwhile the reader is available to pass EMV2000 and PBOC 2.0 and be authenticated by many laboratorial certifications---Visa Wave & Pay Pass (by FIME) and the Bank Card Test Center. There are 6 SAM card slots in the reader which support SAM cards compliant with ISO7816 (T=0 and T=1). The reader supports card-reset of various communication rate; PPSS operation after card-reset; SAM operation of various communication rate. JMY901 needs to be used in conjunction with JMY980 which supports Linux, WinCE6.0 embedded operating system.

  • Qualifications:
  • PCD: NXP RC500,RC531,RC632,RC400;FM1722
  • Working frequency: 13.56MHz
  • The operating frequency of the core board(JMY980): 400MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 100mm (Mifare One, typical distance)
  • SAM card slot: 6 slots (supported ISO7816 T=0 and T=1)
  • Interface: RS232C:1;USB HOST:2;USB SLAVE:1;10/100M Ethernet RJ45;TF card slot:1; 50ohm coaxial cable:2
  • Power supply: DC5V or USB SLAVE
  • Power consumption: 1300mA
  • Dimension: 150mm × 118mm × 20mm
  • Weight: about 100g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • Program: To provide the WinCE6.0 test software source code and the MasterRD.dll dynamic librarie; To provide MasterRD.so dynamic librarie based on Linux.
[Related Categories: Security Project, Other Electronic Accessories ]
[Related Keywords: charge controller, RFID reader, rfid module, 13.56MHz, HF ]
 Sell 13.56MHz RFID Charge controller with display JMY901 Sell 13.56MHz RFID Charge controller with display JMY901

   JMY901 series contactless IC card reader are based the NXP or compatible chip design. The reader supports series IC cards according to ISO14443A, ISO14443B, ISO15693 and ISO7816; various contactless IC card under international standard; especially the contactless CPU cards under ISO14443-4. Meanwhile the reader is available to pass EMV2000 and PBOC 2.0 and be authenticated by many laboratorial certifications---Visa Wave & Pay Pass (by FIME) and the Bank Card Test Center. There are 6 SAM card slots in the reader which support SAM cards compliant with ISO7816 (T=0 and T=1). The reader supports card-reset of various communication rate; PPSS operation after card-reset; SAM operation of various communication rate. JMY901 needs to be used in conjunction with JMY980 which supports Linux, WinCE6.0 embedded operating system.

  • Qualifications:
  • PCD: NXP RC500,RC531,RC632,RC400;FM1722
  • Working frequency: 13.56MHz
  • The operating frequency of the core board(JMY980): 400MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 100mm (Mifare One, typical distance)
  • SAM card slot: 6 slots (supported ISO7816 T=0 and T=1)
  • Interface: RS232C:1;USB HOST:2;USB SLAVE:1;10/100M Ethernet RJ45;TF card slot:1; 50ohm coaxial cable:2
  • Power supply: DC5V or USB SLAVE
  • Power consumption: 1300mA
  • Dimension: 150mm × 118mm × 20mm
  • Weight: about 100g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • Program: To provide the WinCE6.0 test software source code and the MasterRD.dll dynamic librarie; To provide MasterRD.so dynamic librarie based on Linux.
[Related Categories: Security Project, Other Electronic Accessories ]
[Related Keywords: HF, 13.56MHz, rfid module, RFID reader, charge controller ]
advertisements
 Sell 13.56MHz RFID reader/writer module JMY622, Sell 13.56MHz RFID reader/writer module JMY622,

 JMY622 series are 13.56MHz RFID reader/writer module with UART and IIC serial ports. The module would meet EMV2000, EMV2010 and PBOC 2.0 standards. And the module and antenna is linked by 50ohm coaxial line. The impedance between RF module and antenna was tuned by impedance analyzer; so the module has excellent read/write performance and stability. Though the wire can reach 10m, but the performance is good. Normally the wire should be 60cm that is the module\'s best performance and stability. JMY622 adopts surface mount installation form. Small size is a major feature of JMY622. JMY622 has many kinds of funtions and it can support various contactless IC card under international standards. Meanwhile it can support the cards from different suppliers. Designer classified&integrated the operation commands for contactless IC cards. In this situation, the uesr can operate it easily via sending simple commands. The most important features for JMY622 is that it can support contactless IC cards(T=CL) fully. It can send and receive more than 256 Bytes APDU commands and also support FSDI=8.

  • Qualifications:
  • PCD: NXP SL RC400, NXP MF RC500, NXP MF RC531, NXP CL RC632
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 100mm(depending on card and antenna design)
  • • Antenna connection: by 50ohm coaxial line, (recommend 60cm, Max. 10 meters), due to order
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default OFF; Can be set.
  • Interface: IIC, UART(selected by SPS pin, recommend to use IIC)
  • Communication rate: IIC--400Kbps; UART--19.2Kbps/115.2Kbps
  • Max.command length: 511 Bytes
  • Interface level: 3.3V (TTL level; 5V tolerance)
  • Power supply: DC 3.3V + 5V(±0.5V)
  • Power consumption: 100mA
  • Dimension: 22mm×35mm
  • Package: Surface Mount
  • Weight: about 10g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Other Electronic Accessories, Safety Products ]
[Related Keywords: 13.56MHz, HF, rfid module, RFID writer, RFID reader ]
 Sell 13.56MHz RFID reader/writer module JMY620,RC522,RC523 Sell 13.56MHz RFID reader/writer module JMY620,RC522,RC523

   JMY620 series are 13.56MHz RFID reader/writer module with UART and IIC serial ports. And the module and antenna is linked by 50ohm coaxial line. The impedance between RF module and antenna was tuned by impedance analyzer; so the module has excellent read/write performance and stability. Though the wire can reach 10m, but the performance is good. Normally the wire should be 60cm that is the module\'s best performance and stability. JMY620 adopts surface mount installation form. Small size is a major feature of JMY620. JMY620 has many kinds of funtions and it can support various contactless IC card under international standards. Meanwhile it can support the cards from different suppliers. Designer classified&integrated the operation commands for contactless IC cards. In this situation, the uesr can operate it easily via sending simple commands. The most important features for JMY620 is that it can support contactless IC cards(T=CL) fully. It can send and receive more than 256 Bytes APDU commands and also support FSDI=8.

  • Qualifications:
  • PCD: NXP MF RC522, NXP MF RC523
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B
  • Operating distance: 100mm(depending on card and antenna design)
  • • Antenna connection: by 50ohm coaxial line, (recommend 60cm, Max. 10 meters), due to order
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default OFF; Can be set
  • Interface: IIC, UART(selected by SPS pin, recommend to use IIC)
  • Communication rate: IIC--400Kbps; UART--19.2Kbps/115.2Kbps
  • Max.command length: 511 Bytes
  • Interface level: 3.3V (TTL level; 5V tolerance)
  • Power supply: DC 3.3V + 5V(±0.5V)
  • Power consumption: Working mode:80mA; Idle:100uA
  • Dimension: 22mm×35mm
  • Package: Surface Mount
  • Weight: about 10g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Security Project, Other Electronic Accessories ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, 13.56MHz ]
advertisements
 Sell 13.56MHz RFID reader/writer module JMY612,RS232C Sell 13.56MHz RFID reader/writer module JMY612,RS232C

  JMY612 series are RFID reader/writer module with RS232C serial ports. JMY612 has various functions and supports multi ISO/IEC standard of contactless card; the cards from different suppliers. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module through RS232C interface. And the module and antenna are separate design. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. The module and antenna is linked by 50ohm coaxial line. The performance is good, though the wire can reach 10m. Normally the wire should be 60cm that is the module\'s best performance and stability.

  • Qualifications:
  • PCD: NXP RC531
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default ON
  • SAM card slot: 4 slots, 9600bps--115200bps
  • EEPROM: 512 Bytes
  • Interface: RS232C
  • Communication rate: 19200--115200bps
  • Max.command length: 1024 Bytes
  • Interface level: 3.3V(TTL level; 5V tolerance)
  • Power supply: DC 5.0V
  • Power consumption: 150mA
  • Dimension: 80mm×60mm×12mm
  • Weight: about 50g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Other Electronic Accessories, Security Product Agents ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, 13.56MHz ]
 Sell 13.56MHz RFID reader/writer module JMY611 with USB or RS232C Sell 13.56MHz RFID reader/writer module JMY611 with USB or RS232C

  JMY611 series are RFID reader/writer module which have various functions and support multi ISO/IEC standard of contactless card; the cards from different suppliers. The designer combined some frequent used command of RF card, this let user operate the cards with full function by sending simple command. Though the module and antenna are separated design, but the impedance between RF module and antenna was tuned by impedance analyzer, therefore the module has excellent performance and stability.

  • Qualifications:
  • PCD: NXP RC500, RC531, RC632, RC400
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 70mm(depending on card and antenna design)
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default ON
  • EEPROM: 512 Bytes
  • Interface: RS232C or USB
  • Communication rate: IIC--400Kbps, UART--19.2Kbps/115.2Kbps
  • Power supply: DC 5.0V
  • Power consumption: 150mA
  • Dimension: 80mm×60mm×12mm
  • Weight: about 20g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Other Electronic Accessories, Security Project ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, 13.56MHz ]
advertisements
 Sell 13.56MHz RFID reader/writer module JMY610,RS232C,RC531 Sell 13.56MHz RFID reader/writer module JMY610,RS232C,RC531

JMY610 series are RFID reader/writer module with UART and IIC serial ports. JMY610 has various functions and supports multi ISO/IEC standard of contactless card; the cards from different suppliers. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module through IIC or UART interface. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability. And the module and antenna are separate design. 50ohm coaxial line is linked the antenna and module. Normally the wire should be less than 200mm, or it will affect the module\'s performance and stability.

  • Qualifications:
  • PCD: NXP RC531
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B
  • Operating distance: 100mm(depending on card and antenna design)
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default ON
  • EEPROM: 512 Bytes
  • Interface: RS232C
  • Communication rate: IIC--400Kbps, UART--19.2Kbps/115.2Kbps
  • Max.command length: 1024 Bytes
  • Interface level: 3.3V(TTL level; 5V tolerance)
  • Power supply: DC 2.7V ~ 5.0V
  • Power consumption: 150mA
  • Dimension: 87mm×65mm×10mm
  • Weight: about 15g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Other Electronic Accessories, Security Product Agents ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, 13.56MHz ]
 Sell 13.56MHz RFID module JMY609 with USB HID interface Sell 13.56MHz RFID module JMY609 with USB HID interface

 JMY609, based on NXP PCD, is the reader module. The module supports series IC cards according to ISO14443A, ISO14443B and imitates the USB keyboard to read and output the card data. JMY609 is reader module with USB interface (HID standard). In the systems of Windows, Linux and other PC systems support USB keyboard, the module imitates the USB keyboard to operate the card data. With our software and DIP switch, the users can set the reader if to read the number of the card or the data of the card or both. And the data can be positive sequence output or be reverse order output. Meanwhile the users can choose freely the key output such as enter, tab etc. after the output of the number and the data of the card. The default of the JMY609 is configuration mode in factory setting. If you want to let the reader work, you need cofigurate it through the software and input the configuration information to the reader. There are 2 SAM card slots in the reader. If the users need read the SAM card and use the SAM to cooperate with the operation, and then you can contact us, we will help you do the job.

  • Qualifications:
  • PCD: NXP RC522, RC523
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B
  • Operating distance: 80mm (Mifare One, typical distance)
  • SAM card slot: 2 slots, (supported ISO7816 T=0 and T=1)
  • Interface: USB (HID standard)
  • Power supply: DC5V
  • Power consumption: 110mA
  • Dimension: 85mm×58mm
  • Weigh: about 100g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
[Related Categories: Security Project, Other Electronic Accessories ]
[Related Keywords: RFID reader, RFID writer, rfid module, HF, 13.56MHz ]
advertisements
 Sell 13.56MHz RFID module JMY608 with USB HID interface Sell 13.56MHz RFID module JMY608 with USB HID interface

JMY608, based on NXP SL RC400, is the reader module. The module supports series IC cards according to ISO15693, and imitates the USB keyboard to read and output the card data. JMY608 is reader module with USB interface (HID standard). In the systems of Windows, Linux and other PC systems support USB keyboard, the reader imitates the USB keyboard to operate the card data. With our software and DIP switch, the users can set the reader if to read the number of the card or the data of the card or both. And the data can be positive sequence output or be reverse order output. Meanwhile the users can choose freely the key output such as enter, tab and so on after the output of the number and the data of the card. The default of the JMY608 is configuration mode in factory setting. If you want to let the reader work, you need cofigurate it through the software and input the configuration information to the reader.

  • Qualifications:
  • PCD: NXP RC400
  • Working frequency: 13.56MHz
  • RF standard: ISO15693
  • Operating distance: 100mm
  • SAM card slot: no
  • Interface: USB (HID standard)
  • Power supply: DC5V
  • Power consumption: 110mA
  • Dimension: 85mm×58mm
  • Weight: about 100g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
[Related Categories: Other Electronic Accessories, Safety Products ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, HID, 13.56MHz ]
 Sell 13.56MHz RFID module JMY608 with USB HID interface Sell 13.56MHz RFID module JMY608 with USB HID interface

JMY608, based on NXP SL RC400, is the reader module. The module supports series IC cards according to ISO15693, and imitates the USB keyboard to read and output the card data. JMY608 is reader module with USB interface (HID standard). In the systems of Windows, Linux and other PC systems support USB keyboard, the reader imitates the USB keyboard to operate the card data. With our software and DIP switch, the users can set the reader if to read the number of the card or the data of the card or both. And the data can be positive sequence output or be reverse order output. Meanwhile the users can choose freely the key output such as enter, tab and so on after the output of the number and the data of the card. The default of the JMY608 is configuration mode in factory setting. If you want to let the reader work, you need cofigurate it through the software and input the configuration information to the reader.

  • Qualifications:
  • PCD: NXP RC400
  • Working frequency: 13.56MHz
  • RF standard: ISO15693
  • Operating distance: 100mm
  • SAM card slot: no
  • Interface: USB (HID standard)
  • Power supply: DC5V
  • Power consumption: 110mA
  • Dimension: 85mm×58mm
  • Weight: about 100g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
[Related Categories: Other Electronic Accessories, Safety Products ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, HID, 13.56MHz ]
advertisements
 Sell 13.56MHz RFID reader/writer module JMY607(ISO14443,ISO15693) Sell 13.56MHz RFID reader/writer module JMY607(ISO14443,ISO15693)

       JMY607 series are RFID reader/writer module with IIC or UART serial ports. JMY607 has various functions and supports multi ISO/IEC standard of contactless IC card; the cards from different suppliers. The designer combined some frequent used command of RF IC card and then user could operate the cards with full function by sending simple command to the module through IIC or UART interface. The module and antenna are integrated design. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability.

  • Qualifications:
  • PCD: NXP RC531, RC632
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 100mm(depending on card and antenna design)
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default ON
  • EEPROM: 512 Bytes
  • Interface: IIC & UART
  • Communication rate: IIC--400Kbps, UART--19.2Kbps/115.2Kbps
  • Max.command length: 511 Bytes
  • Interface level: 3.3V(TTL level; 5V tolerance)
  • Power supply: DC5.0V
  • Power consumption: 50mA
  • Dimension: 70mm×70mm×10mm
  • Weight: about 20g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
  • ISP: Supported
  • RoHS: Compliant
[Related Categories: Other Electronic Accessories, Safety Products ]
[Related Keywords: rfid module, RFID reader, RFID writer, HF, 13.56MHz ]
 Sell 13.56MHz RFID reader/writer module JMY604 with RS232C interface Sell 13.56MHz RFID reader/writer module JMY604 with RS232C interface

JMY604 series are RFID reader/writer module with UART serial ports. JMY604 has various functions and supports multi ISO/IEC standard of contactless IC card; the cards from different suppliers. The designer combined some frequent used command of RF IC card and then user could operate the cards with full function by sending simple command to the module. The module and antenna are integrated design. The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability.

  • Qualifications:
  • Authenticated: BCTC(the Bank Card Test Center )--contactless Bank Card LEVEL 1
  • PCD: NXP RC500, RC531, RC632
  • Working frequency: 13.56MHz
  • RF standard: ISO14443A, ISO14443B, ISO15693
  • Operating distance: 80mm (Mifare One, typical distance)
  • Anti collision ability: Full function anti collision; be able to process multi-cards simultaneously; be able to set operate single card only
  • Auto detecting card: Supported, default OFF
  • EEPROM: 512 Bytes
  • Interface: RS232C
  • Baud rate: 19200--115200 BPS
  • Power supply: DC5V
  • Power consumption: 80mA
  • Dimension: 80mm×70mm×10mm
  • Weight: about 25g
  • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
  • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
[Related Categories: Other Electrical Equipment, Safety Products ]
[Related Keywords: RFID reader, RFID writer, rfid module, HF, 13.56MHz ]
1 2
Scroll